Determination of the optimum dry film thickness of polyurethane coating using experimentation and mathematical modeling

Authors

  • Anyanwu Kingsley Onyekachi Department of Materials and Metallurgical Engineering, School of Engineering and Engineering Technology, Federal University of Technology Owerri, 460114 Owerri, Imo State, Nigeria https://orcid.org/0000-0002-6648-3290
  • Agha Inya Ndukwe Department of Materials and Metallurgical Engineering, School of Engineering and Engineering Technology, Federal University of Technology Owerri, 460114 Owerri, Imo State, Nigeria https://orcid.org/0000-0002-1723-7026
  • Chukwudike Onuoha Department of Materials and Metallurgical Engineering, School of Engineering and Engineering Technology, Federal University of Technology Owerri, 460114 Owerri, Imo State, Nigeria https://orcid.org/0000-0001-9300-4817
  • Udochukwu Samuel Ikele Department of Materials and Metallurgical Engineering, School of Engineering and Engineering Technology, Federal University of Technology Owerri, 460114 Owerri, Imo State, Nigeria https://orcid.org/0000-0001-5877-5245

DOI:

https://doi.org/10.64171/JAES.6.6.22-32

Keywords:

Modeling, Optimization, DFT, Corrosion, Protective coatings

Abstract

Researchers have shown that dry film thickness (DFT) of corrosion protective coatings is a critical parameter, as it determines the durability and performance of the coating and substrate. In various publications, DFTs have been recommended for polyurethane (PU) coatings but none of the publications showed empirical approach for determining the optimum DFT of corrosion protective coatings, of which this study seeks to achieve. For this study, polyurethane (PU) resin was used as coating, while mild steel coupons were used as the substrate. A total of 63 coupons were produced. The coupons were tagged, weighed, and their initial masses were recorded accordingly. Two experiments were performed; for experiment I, DFTs applied were about 50 μm, 100 μm, and 150 μm. Seven samples were made of each DFT. The samples were submerged in 0.2M dil. HCl solution. Average corrosion rates of the samples were investigated accordingly on weekly and used with corresponding DFTs to calculate the optimum DFTs (t*) in accordance with the proposed model. For experiment II, DFTs applied were 0.25t*, 0.625t*, t*, 1.375t*, and 1.75t*. Seven samples were made of each of the DFTs. The coated samples were used with 7 uncoated (control) to conduct experiment II, following similar procedure adopted in experiment I. Average corrosion rates of the samples were also determined accordingly on weekly basis. The model was also used to estimate corrosion rates of the samples for the various DFTs. Average corrosion rates obtained from experimental results, otherwise referred to as “actual corrosion rate” and those estimated with the model, referred to as “model corrosion rate” were plotted on the same axis against the corresponding DFTs. Parabolic curves were obtained. Chi-square test was conducted to evaluate the association between coating thickness and corrosion rate, taking 0.05 significant level. Also, scatter index (SI), product moment correlation coefficient (R), and Nash-Sutcliffe efficiency coefficient (E) were calculated and used to evaluate the accuracy of the model. Result of Chi-square test shows weak association between DFTs and corrosion rates with (p = 0.4742). Optimum DFT of (110 μm) was obtained from the model, against (110.6 μm) actual. Comparing “model” and “actual” corrosion rates, the proposed model also exhibited good performance: (SI = 3.89; R = 0.96; E = 0.91). Thus, the proposed model can supposedly be used to proffer solution to premature failure of coatings related to inappropriate DFT.

References

Adrian. The ultimate guide to conformal coating thickness measurement ensuring optimal PCB protection, 2025. Available from: https://share.google/2rMFvbJrTfTVrA5Ei. Accessed 2026 Jun 20.

Aisyah R. How to estimate optimum insulation thickness. Chemical Engineering Portal. 2020. Available from: https://missrifka.com/calculation/how-to-estimate-optimum-insulation-thickness.html.

Aljibori H, Al-Amiery A, Kadhum A. Advances in corrosion protection coatings: a comprehensive review. International Journal of Corrosion and Scale Inhibition. 2023;12:1476–1520. doi:10.17675/2305-6894-2023-12-4-6.

Amir S. Use of polyurethane coating to prevent corrosion in oil and gas pipelines transfer. International Journal of Innovation and Applied Studies, 2012, 1. Available from: http://www.issr-journals.org/ijias/. Accessed 2025 Jul 11.

Anand G, Anirbid S. Introduction to pigging & a case study on pigging of an onshore crude oil trunkline. IJLTEMAS, 2016, 5(2).

Anyanwu KO. Parabolic model for optimum dry film thickness (DFT) of corrosion protective coatings. International Research Journal of Multidisciplinary Technovation. 2022;4(4):8–13.

Baur J. Consequences of applying coatings outside of the recommended thickness range. KTA-Tator, 2001. Available from: https://kta.com/kta-university/recommended-coating-thickness/.

D&D Coating Industries Ltd. What is paint coating delamination. UK, 2024.

Ferrum SA. Extruded three-layer polypropylene coating on steel pipes. Ferrum SA. 2022. Available from: https://www.ferrum.com.pl/produkty/wytlaczana-trojwarstwowa-powloka-polipropylenowa-na-rurach-stalowych-lpp/?lang=en.

Forsgren A. Corrosion control through organic coating. CRC Press, 2006, p184.

For laboratory applications. MDPI. 6(4). doi:10.3390/automation6040075.

GZ Industrial Supplies. Understanding different types of professional surface coatings: applications and advantages, 2026.

Herman P, Felita W, Wimala L. Analysis of the effects of abrasive materials and polyurethane coating thickness variation on ASTM A36 steel towards corrosion rates in sea water environments. International Journal of Offshore and Coastal Engineering. 2021;5(1):10–17.

Hitchens L. Delamination. Nexus. 2017. Available from: https://www.conformalcoatinghelp.com/index.php/ebook/troubleshooting/delamination.

Ji H, Liu J, Ye H. Time-series prediction of steel corrosion in concrete using recurrent neural networks. Nondestructive Testing and Evaluation, 2025, 1–20. doi:10.1080/10589759.2025.2456668.

Joshi SS, Patil VJ, Gite VV. High performance coating formulation using multifunctional monomers and reinforcing functional filters for protecting metal substrate. Pigment & Resin Technology, 2025, 54(5). doi:10.1108/PRT-03-2024-0033.

Komalasari S, Utami M, Aziz Y, Irianti R. Corrosion control of carbon steel using banana peel extract as inhibitor in dilute acid solution. IOP Conference Series: Materials Science and Engineering, 2018. Available from: https://www.researchgate.net/publication/324494551_corrosion_control_of_carbon_steel_using_inhibitor_of_banana_peel_extract_in_acid_dilute_solutions. Accessed 2025 Mar 3.

Marlin Steel Wire. What is the average thickness for urethane coating? Marlin Steel Wire Products, 2013.

Onaifo J, Ofabar G, Onaiwu G, Edogun P, Ifijen I. Polyurethane foam: production processes and advanced material characterization. 2025. p. 31–36.

Raghvendra G. Dry film thickness (DFT). Corrosionpedia, 2024. Available from: https://www.corrosionpedia.com/contributors/raghvendra-gopal.

Sean H. Cracking in conformal coating: major causes and preventive strategies. Diamond-MT, 2017. Available from: https://blog.paryleneconformalcoating.com/cracking-conformal-coating/.

Shahbaz A, Siraj A, Sabih A, Faraz A, Majib A. Data driven assessment of corrosion in reinforced concrete structures embedded in clay dominated soils. Scientific Reports. 2025;15:22744. doi:10.1038/341598-025-08526-w.

Somarathna H, Raman S, Mohotti D, Mutalib A, Badri K. The use of polyurethane for structural and infrastructural engineering applications: a state-of-the-art review. Construction and Building Materials. 2018;190:995–1014.

SSPC-PA 2 2022: Procedure for determining conformance to coating thickness requirement. 2022.

Sutha S, Suresh S, Raj B, Ravi K. Transparent alumina based super-hydrophobic self-cleaning coating for solar cell cover glass applications. Solar Energy Materials and Solar Cells. 2017;165:128–137.

Winniki W, Malachowska A, Ambroziak A. Taguchi optimization of the thickness of a coating deposited by LPCS. Archives of Civil and Mechanical Engineering. 2014;14:561–568.

Ying Y, Ping Z, Shang-Xiong Z, Xiao Guang G, Dong-Ming G. Effect of substrate curvature on thickness distribution of polydimethylsiloxane thin film in spin coating process. Chinese Physics B, 2018, 27.

Yunhu Coating. Recommended dry film thickness for coatings, 2026. Available from: https://www.yuhhucoating.com/recommended-dry-film-thickness-industrial-coating/. Accessed 2026 Jun 20.

Downloads

Published

2026-11-12

How to Cite

Onyekachi, A. K., Ndukwe, A. I., Onuoha, C., & Ikele, U. S. (2026). Determination of the optimum dry film thickness of polyurethane coating using experimentation and mathematical modeling. Journal of Advanced Education and Sciences, 6(6), 22–32. https://doi.org/10.64171/JAES.6.6.22-32

Issue

Section

Articles